[Xorp-users] Missing OSPF neighbours

[Atanu Ghosh]

Hi,

Your config files worked fine for me (I changed the interface addresses
for my setup and didn't include the static route). By the way I wouldn't
expect to see any ospf routes, the two routers can already reach each
other.

    Atanu.

Xorp> show ospf4 neighbor 
  Address         Interface             State      ID              Pri  Dead
10.0.1.5         fxp1/fxp1              Full      10.0.0.1         128    33

Xorp> show ospf4 neighbor 
  Address         Interface             State      ID              Pri  Dead
10.0.1.1         xl0/xl0                Full      10.0.0.2         128    35

D>>>>> "Dinesh" == Dinesh Kumar <reach_dinesh at hotmail.com> writes:
    Dinesh> ear XORP users,

    Dinesh> I have configured OSPF using xorp between 2 PCs running linux. I am not able to see any OSPF neighbours in the xorp shell (xorpsh) in both the PCs.

    Dinesh> PC1:(using config1.boot)
    Dinesh> ------------------------------
    Dinesh> dinesh at linux-xorp> show ospf4 neighbor
    Dinesh> Address         Interface             State      ID              Pri  Dead
    Dinesh> dinesh at linux-xorp>

    Dinesh> dinesh at linux-xorp> show route table ipv4 unicast ospf
    Dinesh> dinesh at linux-xorp>

    Dinesh> dinesh at linux-xorp> show ospf4 database
    Dinesh> OSPF link state database, Area 0.0.0.0
    Dinesh> Type       ID               Adv Rtr           Seq      Age  Opt  Cksum  Len
    Dinesh> Router  *10.0.0.2         10.0.0.2         0x80000001   105  0x2  0x260a  36
    Dinesh> dinesh at linux-xorp>


    Dinesh> I am really not sure why there is no adjacency between these two PCs. I have checked the reachability between them also.

    Dinesh> From PC1 to PC2:
    Dinesh> -----------------------
    Dinesh> dinesh at linux-xorp> ping 10.0.0.1
    Dinesh> PING 10.0.0.1 (10.0.0.1) 56(84) bytes of data.
    Dinesh> 64 bytes from 10.0.0.1: icmp_seq=1 ttl=64 time=3.54 ms
    Dinesh> 64 bytes from 10.0.0.1: icmp_seq=2 ttl=64 time=0.204 ms
    Dinesh> 64 bytes from 10.0.0.1: icmp_seq=3 ttl=64 time=0.212 ms
    Dinesh> 64 bytes from 10.0.0.1: icmp_seq=4 ttl=64 time=0.204 ms

    Dinesh> Command interrupted!

    Dinesh> dinesh at linux-xorp>

    Dinesh> From PC2 to PC1:
    Dinesh> ----------------------
    Dinesh> dinesh at linux-xorp2> ping 10.0.0.2
    Dinesh> PING 10.0.0.2 (10.0.0.2) 56(84) bytes of data.
    Dinesh> 64 bytes from 10.0.0.2: icmp_seq=1 ttl=64 time=0.191 ms
    Dinesh> 64 bytes from 10.0.0.2: icmp_seq=2 ttl=64 time=0.182 ms
    Dinesh> 64 bytes from 10.0.0.2: icmp_seq=3 ttl=64 time=0.177 ms

    Dinesh> Command interrupted!

    Dinesh> dinesh at linux-xorp2>

    Dinesh> I have attached the config.boot files of both the PCs. I would be very much obliged if somebody can point out if i have missed anything in config.boot. Thanks in advance.

    Dinesh> Regards,
    Dinesh> Dinesh

    Dinesh> _________________________________________________________________
    Dinesh> Get your free suite of Windows Live services today!
    Dinesh> http://www.get.live.com/wl/all_______________________________________________
    Dinesh> Xorp-users mailing list
    Dinesh> Xorp-users at xorp.org
    Dinesh> http://mailman.ICSI.Berkeley.EDU/mailman/listinfo/xorp-users